Yes, we generally work throughout the tri-cities and surounding areas but we also travel throught the province for many of our larger customers. Drop us a line and see when we will be in your area.

You will see cracks and areas alligatoring. If neglected these areas will usually become pot holes or cause premature base failure.

Asphalt is a porous material, susceptible to oxidation from the sun and damage from chemicals such as gasoline, diesel fuel, oil and antifreeze. Asphalt pavement will also ravel away over time. Sealcoating not only makes your pavement look new, it protects it from oxidation and petroleum spills. Sealcoating should be done every 3 – 5 years depending on use. Sealcoating your pavement allows it to be cleaned easier because it is not porous.

In Ontario most parking lots are layed with 2 lifts of asphalt, with the base asphalt being as thing as 2.5″ and the surface course being 2″.

The damaged asphalt is heated so that it becomes soft, then the area is reworked. Rejuvenating emulsion is sprayed on and new asphalt is applied to fill in any voids. The entire area is them compacted with a vibratory compactor to form a seamless patch that is thermally bonded to the surrounding pavement.

No. Thermal bonding of the Infrared asphalt repair with the surrounding pavement makes the repair an integral piece of the pavement.

Infrared Asphalt repairs are comparable conventional repairs but your selling price will depend on your specific market.

Typical Repairs can be done in 20 minutes or less.

Yes. Infrared uses the existing asphalt which leaves little or no wasted material. In fact, Infrared Asphalt repairs leaves more than 90% less carbon footprint in our environment as compared to the conventional removal and replace method.

No. Infrared restoration is much more cost effective than traditional full depth patching and mill and pave methods. Consider the savings in manpower, time, machinery and materials by not having to cutout, remove, replace, transport and dispose of large quantities of asphalt. In addition the end result is a neat, clean, seamless patch that is thermally bonded to the surrounding asphalt.

No. Infrared can be used economically on large patches and trenches as well. This is achieved by using multiple heats in succession. The larger the machine the more cost effective it will be.

Yes. A correctly installed Infrared repair will restore the damaged area to the condition and useful life of the pavement around the repair. If there is pavement deterioration in the surrounding area it could eventually effect the restoration over time.

No. Infrared addresses the asphalt course or the roadway only. Nothing short of excavating and making repairs to the sub-base will correct this problem. Infrared restoration is still the most effective repair to the asphalt once the sub-base problem is corrected.

Once the repaired surface has returned close to normal surface temperature. This is dependent on the original surface material and inclement weather, but even in poor conditions is usually no longer than 30 minutes.

In short, It’s the HEAT…that what our customers tell us. For a more detailed description please see our What’s different section of our website.

Settlement is very common. Infrared repair is the best solution for this scenario as long as the sub-base (the course under the asphalt) has stopped settling.

It really depends on how much, and how long ! If it is a recent incident you can usually take a good detergent (like dawn) and mix with a little water, and use a scrub brush with fairly stiff bristles. It should break up the stain. Then flush with clean water. If the problem is not taken care of with the above action, you may want to take a pointed object (like a screwdriver) and see how deep you can penetrate the asphalt. That will tell you if the binder has been compromised. Where asphalt pavement is a petroleum derivative any gas or oil that saturates into it will neutralize the binder that makes the asphalt hard. If this happens, you cannot do anything to it that will stiffen it up again. The corrective action would be to remove the contaminated asphalt, and repair with a cold patch product, or call an Asphalt Maintenance company that does infrared repairs.

Very slightly. Results from lab tests that we have received indicate no differences in physical properties or characteristics of the pavement that was tested. Please keep in mind that pavement characteristics change from geographic location to location. Remember, true infrared is a ray and does not depend on excessive amounts of heat to accomplish its task.

Infrared and conventional repair are similar in the respect that you only achieve good results from taking the time and proper steps to insure a quality job. This includes preparation, proper luteing, and correct compaction. If any of these elements are missing then the end result will suffer. We feel that infrared excels in the areas of application, seasonable usage, and the permanence of the repairs.

YES, if done in steps. If you had a single course of asphalt 3 inches thick, the rays will penetrate through the entire course. If you have a 1″ overlay on top of that 3″ course, the rays will penetrate only the overlay, or one coarse at a time. The solution is to rake back the softened course, exposing the next course to be heated. The rays then penetrate the exposed course. Utilizing the proper steps, you can achieve full depth penetration. Of course, in some instances, full depth is not needed nor called for. In the case of many potholes the multiple layers will be exposed to the infrared rays already.

No. Infrared rays are unable to penetrate standing water such as you might find in a bird bath. Any standing pools of water should be swept away prior to heating otherwise the asphalt underneath will not be heated. Moisture or dampness will have no effect on penetration.

If the base is not constructed properly or has been affected by water penetration and heavy loads the Infrared process will dress up the area but the reflective crack will work back through.

Yes. Repairs can be done year round in the coldest of temperatures. The outside temperatures will not affect your ability to have a seamless repair but will lengthen the time it takes to heat the asphalt to the full depth of the repair. Throughout the summer IPR saves and stockpiles any left over asphalt at the end of the day. We are able to reheat this with infrared heat to create and Hot asphalt in the coldest of days.

Two reports explain how infrared will affect the asphalt binder, one from the University of Auburn (report), the other the results of a test performed by the National Highways Institute (report). The reports cover the physical, chemical and rheological properties of the binder following tests using our Infrared joint-heater on a busy 4 lane highway having an overlay done. The application is somewhat more arduous than a repair on a pot-hole on a suburban road because joint-failure on a major highway has significant effects on the highway’s life-cycle costs!